sales@gbic.ph
8244-8412/8244-8413
941 Benavidez St. Binondo Manila
For Wholesale & Customer Support, contact us directly through 8244-8412
Single row tapered roller bearings are designed to accommodate combined loads, i.e. simultaneously acting radial and axial loads. The projection lines of the raceways meet at a common point on the bearing axis to provide a true rolling action and therefore low frictional moments during operation. The axial load carrying capacity of tapered roller bearings increases with increasing contact angle.
- Low friction
The optimized roller end design and surface finish on the flange promote lubricant film formation, resulting in lower friction. This also reduces frictional heat and flange wear. In addition, the bearings can better maintain preload and run at reduced noise levels.
- Long service life
The crowned raceway profiles of basic design bearings optimize the load distribution along the contact surfaces, reduce stress peaks at the roller ends, and reduce the sensitivity to misalignment and shaft deflection compared with conventional straight raceway profiles.
- Enhanced operational reliability
Optimized surface finish on the contact surfaces of the rollers and raceways supports the formation of a hydrodynamic lubricant film.
- Rigid bearing application
A single row tapered roller bearing is typically adjusted against a second tapered roller bearing. By applying a preload, a rigid bearing application can be achieved.
.png)
Single row cylindrical roller bearings are available in many designs, series and sizes.
Double row cylindrical roller bearings are available in several designs with a cylindrical or tapered bore.
Four-row cylindrical roller bearings are used almost exclusively for the roll necks of rolling mill stands, calenders and roller presses.
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Suspendisse varius enim in eros elementum tristique. Duis cursus, mi quis viverra ornare, eros dolor interdum nulla, ut commodo diam libero vitae erat. Aenean faucibus nibh et justo cursus id rutrum lorem imperdiet. Nunc ut sem vitae risus tristique posuere.
-design-with-M-cage.png)
Single row angular contact ball bearings can accommodate axial loads in one direction only.
The design of the double row angular contact ball bearings corresponds to two single row angular contact ball bearings arranged back-to-back.
Four-point contact ball bearings are radial single row angular contact ball bearings with raceways that are designed to support axial loads in both directions.
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Suspendisse varius enim in eros elementum tristique. Duis cursus, mi quis viverra ornare, eros dolor interdum nulla, ut commodo diam libero vitae erat. Aenean faucibus nibh et justo cursus id rutrum lorem imperdiet. Nunc ut sem vitae risus tristique posuere.
Single row tapered roller bearings are designed to accommodate combined loads, i.e. simultaneously acting radial and axial loads.
The assortment of matched single row tapered roller bearings is based on popular sizes of single row tapered roller bearings.
Double row tapered roller bearings can accommodate heavy radial loads, axial loads in both directions and have a high degree of stiffness.
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Suspendisse varius enim in eros elementum tristique. Duis cursus, mi quis viverra ornare, eros dolor interdum nulla, ut commodo diam libero vitae erat. Aenean faucibus nibh et justo cursus id rutrum lorem imperdiet. Nunc ut sem vitae risus tristique posuere.
Cylindrical roller thrust bearings are designed to accommodate heavy axial loads and impact loads.
Needle roller thrust bearings are fitted with a form-stable cage to reliably retain and guide a large number of needle rollers.
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Suspendisse varius enim in eros elementum tristique. Duis cursus, mi quis viverra ornare, eros dolor interdum nulla, ut commodo diam libero vitae erat. Aenean faucibus nibh et justo cursus id rutrum lorem imperdiet. Nunc ut sem vitae risus tristique posuere.
Pillow block bearing units consist of an insert bearing mounted in a housing, which can be bolted to a support surface.
Flanged bearing units consist of an insert bearing mounted in a housing, which can be bolted to a machine wall or frame.
The take-up bearing unit assortment comprises of insert bearing series and designs, with the main differences between the take-up units being the housing design, the locking method onto the shaft, the sealing solution, and the options for end covers and back seals.
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Suspendisse varius enim in eros elementum tristique. Duis cursus, mi quis viverra ornare, eros dolor interdum nulla, ut commodo diam libero vitae erat. Aenean faucibus nibh et justo cursus id rutrum lorem imperdiet. Nunc ut sem vitae risus tristique posuere.
Let us know about your needs through a dedicated agent so we can better customize our rates and shipment for your business. Send a message today!
.png)
